PaddleWise by thread

From: E. Sullivan <sullivaned_at_pop.mts.kpnw.org>
subject: [Paddlewise] Werner Paddles
Date: Wed, 08 Mar 2000 13:03:14 -0800
Dr. Bill;

My Werner is currently a back-up/loaner, so doesn't get
heavy usage. Has been reliable except for one thing, which
probably applies to all take-down models. Oil the locking
mechanism. Maybe carry a spare. I tossed my paddle on to
sand after a surf landing and it broke (meaning the
spring-like button thing). I whittled a dowel to fix it, but
it was annoying.

***************************************************************************
PaddleWise Paddling Mailing List - All postings copyright the author and not
to be reproduced outside PaddleWise without author's permission
Submissions:     paddlewise_at_lists.intelenet.net
Subscriptions:   paddlewise-request_at_lists.intelenet.net
Website:         http://www.paddlewise.net/
***************************************************************************
From: Rob Cookson <rob_cookson_at_mindspring.com>
subject: RE: [Paddlewise] Werner Paddles
Date: Wed, 8 Mar 2000 18:08:16 -0800
I have owned several Werner paddles over the years and been happy with them.
I currently own 2 of their ultra-light carbon Kauai's and am  very pleased.
I have abused the Kauai's in ways that would make the Werner folks cringe
and they are still holding up well.

Regarding the weight difference.  The new Werner paddles are really light in
both glass and carbon.  I do find that the reduced swing weight with the
carbon blades is very worthwhile even though the total weight differance is
not that great.  Unless the money is going to squeeze out some other
important purchase I would say definately go carbon.

Regarding the ferrule button.  It is rare that these buttons fail but it
does happen.  Werner  sells spares.  If you do experience a field failure I
would suggest simply using a piece of duct tape to secure the joint in the
desired position.  I'm not a fan of using oil on my paddle for a couple of
reasons, I find that it tends to attract and hold gunk at the ferrule, and
if it seeps out and on to the shaft it's kind'a slippery.  If you are
concerned with corrosion I would reccomend a good fresh water rinsing after
paddling and periodic inspection of the button.

But of course your mileage may vary.

--
Rob Cookson
"They that can give up essential liberty to obtain a little temporary safety
deserve neither liberty nor safety"
Benjamin Franklin

> -----Original Message-----
> From: owner-paddlewise_at_lists.intelenet.net
> [mailto:owner-paddlewise_at_lists.intelenet.net]On Behalf Of E. Sullivan
> Sent: Wednesday, March 08, 2000 1:03 PM
> To: p w
> Subject: [Paddlewise] Werner Paddles
>
>
> Dr. Bill;
>
> My Werner is currently a back-up/loaner, so doesn't get
> heavy usage. Has been reliable except for one thing, which
> probably applies to all take-down models. Oil the locking
> mechanism. Maybe carry a spare. I tossed my paddle on to
> sand after a surf landing and it broke (meaning the
> spring-like button thing). I whittled a dowel to fix it, but
> it was annoying.
>
> ******************************************************************
> *********
> PaddleWise Paddling Mailing List - All postings copyright the
> author and not
> to be reproduced outside PaddleWise without author's permission
> Submissions:     paddlewise_at_lists.intelenet.net
> Subscriptions:   paddlewise-request_at_lists.intelenet.net
> Website:         http://www.paddlewise.net/
> ******************************************************************
> *********

***************************************************************************
PaddleWise Paddling Mailing List - All postings copyright the author and not
to be reproduced outside PaddleWise without author's permission
Submissions:     paddlewise_at_lists.intelenet.net
Subscriptions:   paddlewise-request_at_lists.intelenet.net
Website:         http://www.paddlewise.net/
***************************************************************************

This archive was generated by hypermail 2.4.0 : Thu Aug 21 2025 - 16:33:10 PDT